Dell CMC Temperature sensor has detected a failure value.
Dell CMC Temperature sensor has detected a failure value
Probable causes and corresponding resolutions for this condition are:
Cause | Resolutions |
The system board <name> temperature is less than the lower critical threshold. | Check system operating environment. |
The system board <name> temperature is greater than the upper critical threshold. | Check system operating environment and review event log for fan failures. |
The system board <name> temperature is outside of range. | Check system operating environment and review event log for fan failures. |
The memory module <number> temperature is less than the lower critical threshold. | Check system operating environment. |
The memory module <number> temperature is greater than the upper critical threshold. | Check system operating environment and review event log for fan failures. |
The memory module <number> temperature is outside of range. | Check system operating environment and review event log for fan failures. |
The <name> temperature is less than the lower critical threshold. | Check system operating environment. |
The <name> temperature is greater than the upper critical threshold. | Check system operating environment and review event log for fan failures. |
The <name> temperature is outside of range. | Check system operating environment and review event log for fan failures. |
The system inlet temperature is less than the lower critical threshold. | Check system operating environment. |
The system inlet temperature is greater than the upper critical threshold. | Check system operating environment. |
The system inlet temperature is outside of range. | Check system operating environment. |
Disk drive bay temperature is less than the lower critical threshold. | Check system operating environment. |
Disk drive bay temperature is greater than the upper critical threshold. | Check system operating environment. |
Disk drive bay temperature is outside of range. | Check system operating environment and review event log for fan failures. |
The control panel temperature is less than the lower critical threshold. | Check system operating environment. |
The control panel temperature is greater than the upper critical threshold. | Check system operating environment. |
The control panel temperature is outside of range. | Check system operating environment and review event log for fan failures. |
Insufficient system cooling detected, system is shutdown. | Check system operating environment. |
CPU <number> temperature is less than the lower critical threshold. | Check system operating environment. |
CPU <number> temperature is greater than the upper critical threshold. | Check system operating environment and review event log for fan failures. |
CPU <number> temperature is outside of range. | Check system operating environment and review event log for fan failures. |
Launch the CMC Console to debug further.
Target | Dell.ModularChassis.CMC | ||
Category | AvailabilityHealth | ||
Enabled | True | ||
Alert Generate | True | ||
Alert Severity | Error | ||
Alert Priority | Normal | ||
Remotable | True | ||
Alert Message |
|
ID | Module Type | TypeId | RunAs |
---|---|---|---|
DS | DataSource | Dell.SNMPTrap.DSMT | Default |
Alert | WriteAction | System.Health.GenerateAlert | Default |
<Rule ID="Dell.ModularChassis.CMC2161" Enabled="true" Target="DAD!Dell.ModularChassis.CMC" ConfirmDelivery="false" Remotable="true" Priority="Normal" DiscardLevel="100">
<Category>AvailabilityHealth</Category>
<DataSources>
<DataSource ID="DS" TypeID="Dell.SNMPTrap.DSMT">
<IP>$Target/Property[Type="DAD!Dell.ModularChassis.CMC"]/IPAddress$</IP>
<CommunityString>$Target/Property[Type="DAD!Dell.ModularChassis.CMC"]/CommunityString$</CommunityString>
<ServiceTag>$Target/Property[Type="DAD!Dell.ModularChassis.CMC"]/ServiceTag$</ServiceTag>
<Status>Critical</Status>
<Severity>2</Severity>
<AllTraps>false</AllTraps>
<OIDProps>
<OIDProp>.1.3.6.1.4.1.674.10892.2.21.0.2161</OIDProp>
</OIDProps>
<EventOriginId>$Target/Id$</EventOriginId>
<PublisherId>$Target/Id$</PublisherId>
<PublisherName>Snmp Event</PublisherName>
<Channel>SnmpEvent</Channel>
<LoggingComputer/>
<EventNumber>2161</EventNumber>
<EventCategory>5</EventCategory>
<EventLevel>10</EventLevel>
<UserName/>
<Params/>
</DataSource>
</DataSources>
<WriteActions>
<WriteAction ID="Alert" TypeID="SystemHealth!System.Health.GenerateAlert">
<Priority>1</Priority>
<Severity>2</Severity>
<AlertMessageId>$MPElement[Name="Dell.ModularChassis.CMC.Rule2161"]$</AlertMessageId>
<AlertParameters>
<AlertParameter1>$Data/EventData/DataItem/Property[@Name="Status"]$</AlertParameter1>
<AlertParameter2>$Data/EventData/DataItem/Property[@Name="EventNumber"]$</AlertParameter2>
</AlertParameters>
<Suppression>
<SuppressionValue>$Data/EventData/DataItem/Property[@Name="EventNumber"]$</SuppressionValue>
<SuppressionValue>$Data/EventData/DataItem/Property[@Name="ServiceTag"]$</SuppressionValue>
<SuppressionValue>$Data/EventData/DataItem/Property[@Name="Severity"]$</SuppressionValue>
<SuppressionValue>$Data/EventData/DataItem/Property[@Name="drsCA2MessageID"]$</SuppressionValue>
<SuppressionValue>$Data/EventData/DataItem/Property[@Name="drsCA2Message"]$</SuppressionValue>
<SuppressionValue>$Data/EventData/DataItem/Property[@Name="drsCA2FQDD"]$</SuppressionValue>
<SuppressionValue>$Data/EventData/DataItem/Property[@Name="drsChassisServiceTag"]$</SuppressionValue>
</Suppression>
<Custom1>Alert Message ID = $Data/EventData/DataItem/Property[@Name="drsCA2MessageID"]$</Custom1>
<Custom2>Alert Message = $Data/EventData/DataItem/Property[@Name="drsCA2Message"]$</Custom2>
<Custom3>Alert FQDD = $Data/EventData/DataItem/Property[@Name="drsCA2FQDD"]$</Custom3>
<Custom4>Alert Chassis Service Tag = $Data/EventData/DataItem/Property[@Name="drsChassisServiceTag"]$</Custom4>
<Custom5>Alert Status = $Data/EventData/DataItem/Property[@Name="drsCA2AlertStatus"]$</Custom5>
<Custom6>Alert Global Status = $Data/EventData/DataItem/Property[@Name="drsGlobalCurrStatus"]$</Custom6>
<Custom7>Alert Chassis Location = $Data/EventData/DataItem/Property[@Name="drsProductChassisLocation"]$</Custom7>
<Custom8>Alert Chassis Name = $Data/EventData/DataItem/Property[@Name="drsProductChassisName"]$</Custom8>
<Custom9/>
<Custom10/>
</WriteAction>
</WriteActions>
</Rule>