Dell Remote Access : Server : System Amperage is in critical state

Dell.iDRAC7.SNMPTrap.2177 (Rule)

Knowledge Base article:

Summary

System Amperage critical state alert

Causes

System Amperage has generated critical alert. Probable causes and corresponding resolutions for this condition are:

Cause	Resolutions
The system board <name> current is less than the lower critical threshold.	Review system power policy, check system logs for power related failures, and review system configuration changes.
The system board <name> current is greater than the upper critical threshold.	Review system power policy, check system logs for power related failures, and review system configuration changes.
The system board <name> current is outside of range.	Review system power policy, check system logs for power related failures, and review system configuration changes.
Disk drive bay <name> current is less than the lower critical threshold.	Review system power policy, check system logs for power related failures, and review system configuration changes.
Disk drive bay <name> current is greater than the upper critical threshold.	Review system power policy, check system logs for power related failures, and review system configuration changes.
Disk drive bay <name> current is outside of range.	Review system power policy, check system logs for power related failures, and review system configuration changes.
System level current is less than the lower critical threshold.	Review system power policy, check system logs for power related failures, and review system configuration changes.
System level current is greater than the upper critical threshold.	Review system power policy, check system logs for power related failures, and review system configuration changes.
System level current is outside of range.	Review system power policy, check system logs for power related failures, and review system configuration changes.

Resolutions

Additional information on this issue may be available. Launch the DRAC or OMSA Console to debug further.

Element properties:

Target

Dell.RemoteAccess.iDRAC7

Category

AvailabilityHealth

Enabled

True

Alert Generate

True

Alert Severity

Error

Alert Priority

Normal

Remotable

True

Alert Message

Dell Remote Access : Server : System Amperage is in critical state

{0}

Member Modules:

ID	Module Type	TypeId	RunAs
DS	DataSource	System.NetworkManagement.SnmpTrapEventProvider	Default
Alert	WriteAction	System.Health.GenerateAlert	Default

Source Code:

<Rule ID="Dell.iDRAC7.SNMPTrap.2177" Enabled="true" Target="DAD!Dell.RemoteAccess.iDRAC7" ConfirmDelivery="false" Remotable="true" Priority="Normal" DiscardLevel="100">

  <Category>AvailabilityHealth</Category>

  <DataSources>

    <DataSource ID="DS" TypeID="Node!System.NetworkManagement.SnmpTrapEventProvider">

      <IP>$Target/Property[Type="DAD!Dell.RemoteAccess.RAC"]/IPAddress$</IP>

      <OIDProps>

        <OIDProp>.1.3.6.1.4.1.674.10892.5.3.2.1.0.2177</OIDProp>

      </OIDProps>

      <EventOriginId>$Target/Id$</EventOriginId>

      <PublisherId>$Target/Id$</PublisherId>

      <PublisherName>iDRAC</PublisherName>

      <Channel>SnmpEvent</Channel>

      <LoggingComputer/>

      <EventNumber>2177</EventNumber>

      <EventCategory>5</EventCategory>

      <EventLevel>10</EventLevel>

      <UserName/>

      <Params/>

    </DataSource>

  </DataSources>

  <WriteActions>

    <WriteAction ID="Alert" TypeID="SystemHealth!System.Health.GenerateAlert">

      <Priority>1</Priority>

      <Severity>2</Severity>

      <AlertName/>

      <AlertDescription/>

      <AlertOwner/>

      <AlertMessageId>$MPElement[Name="Dell.iDRAC7.SNMPTrap.2177.Rule"]$</AlertMessageId>

      <AlertParameters>

        <AlertParameter1>$Data/EventData/DataItem/SnmpVarBinds/SnmpVarBind[4]/Value$</AlertParameter1>

      </AlertParameters>

      <Suppression>

        <SuppressionValue>$Data/EventDisplayNumber$</SuppressionValue>

        <SuppressionValue>$Data/Channel$</SuppressionValue>

        <SuppressionValue>$Data/PublisherName$</SuppressionValue>

        <SuppressionValue>$Data/LoggingComputer$</SuppressionValue>

        <SuppressionValue>$Data/EventCategory$</SuppressionValue>

        <SuppressionValue>$Data/EventLevel$</SuppressionValue>

        <SuppressionValue>$Data/UserName$</SuppressionValue>

        <SuppressionValue>$Data/EventNumber$</SuppressionValue>

        <SuppressionValue>$Data/EventData/DataItem/SnmpVarBinds/SnmpVarBind[3]/Value$</SuppressionValue>

        <SuppressionValue>$Data/EventData/DataItem/SnmpVarBinds/SnmpVarBind[4]/Value$</SuppressionValue>

        <SuppressionValue>$Data/EventData/DataItem/SnmpVarBinds/SnmpVarBind[6]/Value$</SuppressionValue>

        <SuppressionValue>$Data/EventData/DataItem/SnmpVarBinds/SnmpVarBind[8]/Value$</SuppressionValue>

      </Suppression>

      <Custom1>Alert Message ID = $Data/EventData/DataItem/SnmpVarBinds/SnmpVarBind[3]/Value$ </Custom1>

      <Custom2>Alert Message = $Data/EventData/DataItem/SnmpVarBinds/SnmpVarBind[4]/Value$ </Custom2>

      <Custom3>Alert Status = $Data/EventData/DataItem/SnmpVarBinds/SnmpVarBind[5]/Value$ </Custom3>

      <Custom4>Alert Service Tag = $Data/EventData/DataItem/SnmpVarBinds/SnmpVarBind[6]/Value$ </Custom4>

      <Custom5>Alert FQDN = $Data/EventData/DataItem/SnmpVarBinds/SnmpVarBind[7]/Value$ </Custom5>

      <Custom6>Alert FQDD = $Data/EventData/DataItem/SnmpVarBinds/SnmpVarBind[8]/Value$ </Custom6>

      <Custom7/>

      <Custom8/>

      <Custom9/>

      <Custom10/>

    </WriteAction>

  </WriteActions>

</Rule>