This error can occur when the creation of a constraint failed but for some reason the creation was not completely rolled back. It can also be caused by data consistency issue with the system tables in the database where the table listed in the message resides.
This error can occur when the creation of a constraint failed but for some reason the creation was not completely rolled back. It can also be caused by data consistency issue with the system tables in the database where the table listed in the message resides.
HARDWARE FAILURE
Run hardware diagnostics and correct any problems. Also, examine the Linux system and application logs and the SQL Server error log to see if the error occurred as the result of hardware failure. Fix any hardware related problems.
If you have persistent data corruption problems, try to swap out different hardware components to isolate the problem. Check to ensure that your system does not have write caching enabled on the disk controller. If you suspect this to be the case, contact your hardware vendor.
Finally, you might find it beneficial to switch to a completely new hardware system, including reformatting the disk drives and reinstalling the operating system.
RESTORE FROM BACKUP
If the problem is not hardware related and a known clean backup is available, restore the database from the backup.
DBCC CHECKDB
If no clean backup is available, execute DBCC CHECKDB without a repair clause to determine the extent of the corruption. DBCC CHECKDB will recommend a repair clause to use. Then, execute DBCC CHECKDB with the appropriate repair clause to repair the corruption.
CAUTION: If you are unsure what effect DBCC CHECKDB with a repair clause has on your data, contact your primary support provider before executing this statement.
If running DBCC CHECKDB with one of the repair clauses does not correct the problem, contact your primary support provider.
If the error still occurs once, there are no errors reported by DBCC CHECKDB, script out the constraints, drop the constraints, and then recreate the constraints. If you still receive the error, transfer the data into a new table and drop the existing table.
Name | Description | Default Value |
Enabled | Enables or disables the workflow. | Yes |
Interval (seconds) | The recurring interval of time in seconds in which to run the workflow. | 300 |
Priority | Defines Alert Priority. | 1 |
Severity | Defines Alert Severity. | 1 |
Synchronization Time | Synchronization Time |
|
Timeout (seconds) | Specifies the time the workflow is allowed to run before being closed and marked as failed. | 200 |
Timeout for database connection (seconds) | The workflow will fail and register an event, if it cannot access the database during the specified period. | 15 |
Target | Microsoft.SQLServer.Linux.DBEngine | ||
Category | EventCollection | ||
Enabled | True | ||
Alert Generate | True | ||
Alert Severity | Warning | ||
Alert Priority | Normal | ||
Remotable | True | ||
Alert Message |
| ||
Comment | Mom2017ID='{F23E8397-4438-493B-A4DF-3C6A93B12E6A}';MOM2017GroupID={467ECC75-C5DA-42BD-955C-A73BBB51AF74} |
ID | Module Type | TypeId | RunAs |
---|---|---|---|
_F6DA1507_12AF_11D3_AB21_00A0C98620CE_ | DataSource | Microsoft.SQLServer.Linux.DataSource.EventCollectionFiltered | Default |
GenerateAlert | WriteAction | System.Health.GenerateAlert | Default |
<Rule ID="Microsoft.SQLServer.Linux.EventRule.DBEngine.Could_not_find_CHECK_constraint_although_the_table_is_flagged_as_having_one_1_5_Rule" Target="SqlDiscL!Microsoft.SQLServer.Linux.DBEngine" Enabled="true" ConfirmDelivery="true" Remotable="true" Comment="Mom2017ID='{F23E8397-4438-493B-A4DF-3C6A93B12E6A}';MOM2017GroupID={467ECC75-C5DA-42BD-955C-A73BBB51AF74}">
<Category>EventCollection</Category>
<DataSources>
<DataSource ID="_F6DA1507_12AF_11D3_AB21_00A0C98620CE_" Comment="{F6DA1507-12AF-11D3-AB21-00A0C98620CE}" TypeID="Microsoft.SQLServer.Linux.DataSource.EventCollectionFiltered">
<MachineName>$Target/Property[Type="SqlCoreLib!Microsoft.SQLServer.Core.DBEngine"]/MachineName$</MachineName>
<InstanceName>$Target/Property[Type="SqlCoreLib!Microsoft.SQLServer.Core.DBEngine"]/InstanceName$</InstanceName>
<ConnectionString>$Target/Property[Type="SqlCoreLib!Microsoft.SQLServer.Core.DBEngine"]/ConnectionString$</ConnectionString>
<SqlTimeoutSeconds>15</SqlTimeoutSeconds>
<TimeoutSeconds>200</TimeoutSeconds>
<IntervalSeconds>300</IntervalSeconds>
<SyncTime/>
<EventDisplayNumber>433</EventDisplayNumber>
</DataSource>
</DataSources>
<WriteActions>
<WriteAction ID="GenerateAlert" TypeID="Health!System.Health.GenerateAlert">
<Priority>1</Priority>
<Severity>1</Severity>
<AlertMessageId>$MPElement[Name="Microsoft.SQLServer.Linux.EventRule.DBEngine.Could_not_find_CHECK_constraint_although_the_table_is_flagged_as_having_one_1_5_Rule.AlertMessage"]$</AlertMessageId>
<AlertParameters>
<AlertParameter1>Event ID: $Data/Property[@Name='EventID']$. $Data/Property[@Name='Message']$</AlertParameter1>
</AlertParameters>
<Suppression>
<SuppressionValue/>
</Suppression>
</WriteAction>
</WriteActions>
</Rule>