Dell CMC SNMP Trap : Current sensor has detected a failure value

Dell.ModularChassis.CMC2177 (Rule)

Dell CMC has generated current sensor failure trap.

Knowledge Base article:

Summary

Dell CMC Current sensor has detected a failure value.

Causes

Probable causes and corresponding resolutions for this condition are:

Cause	Resolutions
The system board < name > current is less than the lower critical threshold.	Review system power policy, check system logs for power related failures, and review system configuration changes.
The system board < name > current is greater than the upper critical threshold.	Review system power policy, check system logs for power related failures, and review system configuration changes.
The system board < name > current is outside of range.	Review system power policy, check system logs for power related failures, and review system configuration changes.
Disk drive bay < name > current is less than the lower critical threshold.	Review system power policy, check system logs for power related failures, and review system configuration changes.
Disk drive bay < name > current is greater than the upper critical threshold.	Review system power policy, check system logs for power related failures, and review system configuration changes.
Disk drive bay < name > current is outside of range.	Review system power policy, check system logs for power related failures, and review system configuration changes.
System level current is less than the lower critical threshold.	Review system power policy, check system logs for power related failures, and review system configuration changes.
System level current is greater than the upper critical threshold.	Review system power policy, check system logs for power related failures, and review system configuration changes.
System level current is outside of range.	Review system power policy, check system logs for power related failures, and review system configuration changes.
Chassis power level current is less than the lower critical threshold.	Review system power policy, check system logs for power related failures, and review system configuration changes.
Chassis power level current is greater than the upper critical threshold.	Review system power policy, check system logs for power related failures, and review system configuration changes.
Chassis power level current is outside of range.	Review system power policy, check system logs for power related failures, and review system configuration changes.

Resolutions

Launch the CMC Console to debug further.

Element properties:

Target

Dell.ModularChassis.CMC

Category

AvailabilityHealth

Enabled

True

Alert Generate

True

Alert Severity

Error

Alert Priority

Normal

Remotable

True

Alert Message

Dell Chassis Management Controller trap : Current sensor has detected a failure value

Dell CMC has generated current sensor failure trap.

Member Modules:

ID	Module Type	TypeId	RunAs
DS	DataSource	Dell.SNMPTrap.DSMT	Default
Alert	WriteAction	System.Health.GenerateAlert	Default

Source Code:

<Rule ID="Dell.ModularChassis.CMC2177" Enabled="true" Target="DAD!Dell.ModularChassis.CMC" ConfirmDelivery="false" Remotable="true" Priority="Normal" DiscardLevel="100">

  <Category>AvailabilityHealth</Category>

  <DataSources>

    <DataSource ID="DS" TypeID="Dell.SNMPTrap.DSMT">

      <IP>$Target/Property[Type="DAD!Dell.ModularChassis.CMC"]/IPAddress$</IP>

      <ServiceTag>$Target/Property[Type="DAD!Dell.ModularChassis.CMC"]/ServiceTag$</ServiceTag>

      <Status>Critical</Status>

      <Severity>2</Severity>

      <AllTraps>false</AllTraps>

      <OIDProps>

        <OIDProp>.1.3.6.1.4.1.674.10892.2.21.0.2177</OIDProp>

      </OIDProps>

      <EventOriginId>$Target/Id$</EventOriginId>

      <PublisherId>$Target/Id$</PublisherId>

      <PublisherName>Snmp Event</PublisherName>

      <Channel>SnmpEvent</Channel>

      <LoggingComputer/>

      <EventNumber>2177</EventNumber>

      <EventCategory>5</EventCategory>

      <EventLevel>10</EventLevel>

      <UserName/>

      <Params/>

    </DataSource>

  </DataSources>

  <WriteActions>

    <WriteAction ID="Alert" TypeID="SystemHealth!System.Health.GenerateAlert">

      <Priority>1</Priority>

      <Severity>2</Severity>

      <AlertMessageId>$MPElement[Name="Dell.ModularChassis.CMC.Rule2177"]$</AlertMessageId>

      <AlertParameters>

        <AlertParameter1>$Data/EventData/DataItem/Property[@Name="Status"]$</AlertParameter1>

        <AlertParameter2>$Data/EventData/DataItem/Property[@Name="EventNumber"]$</AlertParameter2>

      </AlertParameters>

      <Suppression>

        <SuppressionValue>$Data/EventData/DataItem/Property[@Name="EventNumber"]$</SuppressionValue>

        <SuppressionValue>$Data/EventData/DataItem/Property[@Name="ServiceTag"]$</SuppressionValue>

        <SuppressionValue>$Data/EventData/DataItem/Property[@Name="Severity"]$</SuppressionValue>

        <SuppressionValue>$Data/EventData/DataItem/Property[@Name="drsCA2MessageID"]$</SuppressionValue>

        <SuppressionValue>$Data/EventData/DataItem/Property[@Name="drsCA2Message"]$</SuppressionValue>

        <SuppressionValue>$Data/EventData/DataItem/Property[@Name="drsCA2FQDD"]$</SuppressionValue>

        <SuppressionValue>$Data/EventData/DataItem/Property[@Name="drsChassisServiceTag"]$</SuppressionValue>

      </Suppression>

      <Custom1>Alert Message ID = $Data/EventData/DataItem/Property[@Name="drsCA2MessageID"]$</Custom1>

      <Custom2>Alert Message = $Data/EventData/DataItem/Property[@Name="drsCA2Message"]$</Custom2>

      <Custom3>Alert FQDD = $Data/EventData/DataItem/Property[@Name="drsCA2FQDD"]$</Custom3>

      <Custom4>Alert Chassis Service Tag = $Data/EventData/DataItem/Property[@Name="drsChassisServiceTag"]$</Custom4>

      <Custom5>Alert Status = $Data/EventData/DataItem/Property[@Name="drsCA2AlertStatus"]$</Custom5>

      <Custom6>Alert Global Status = $Data/EventData/DataItem/Property[@Name="drsGlobalCurrStatus"]$</Custom6>

      <Custom7>Alert Chassis Location = $Data/EventData/DataItem/Property[@Name="drsProductChassisLocation"]$</Custom7>

      <Custom8>Alert Chassis Name = $Data/EventData/DataItem/Property[@Name="drsProductChassisName"]$</Custom8>

      <Custom9/>

      <Custom10/>

    </WriteAction>

  </WriteActions>

</Rule>